APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 110

Страница: 110 / 394

•

Indication on Axone always down: check the connector: if not OK, restore; if it is OK, dis-

connect the two terminals from the sensor and check continuity to ground of PIN 1: if there

is no continuity, restore the cable harness; if there is, replace the sensor

•

Indication on Axone always up: disconnect the terminals from the sensor and check if there

is continuity between the two PINS, with stand down: if there is continuity, replace the sensor;

if the circuit is open, it means that on the brown/green cable from sensor PIN 2 to PIN 38 of

connector B (BLUE) there is a short circuit to ground: restore the cable harness

Bank angle sensor

FALL SENSOR

Function

it tells the vehicle position to the control unit.

Operation / Operating principle

When the sensor is inverted, the circuit is closed

to ground: When the Marelli control unit detects

this ground connection, it does not enable start-up

or shuts off the engine.

Level in wiring diagram:

Start-up enabling

switches.

Location:

•

on the vehicle: under the saddle, front

area near the control unit

•

connector: near the sensor

Electrical characteristics:

•

Sensor in vertical position: open circuit

(resistance: 62 kOhm)

•

Sensor inverted: closed circuit (con-

tinuity)

Pin-out:

1. Ground connection

2. Voltage 5V

THE CONNECTION DIAGRAMS ARE IN THE ELECTRICAL SYSTEM SECTIONS; PAY ATTENTION

TO THESE DIAGRAMS AS THEY SHOW THE CONNECTOR/COMPONENT AS VIEWED FROM

THE CABLE HARNESS SIDE, THAT IS LOOKING AT THE CABLES WHEN GOING OUT OF THE

"MAIN" CABLE HARNESS AND INTO THE CONNECTOR/COMPONENT.

CAUTION

Electrical system

MSS Mana GT ABS

ELE SYS - 110

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды