APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 50

Страница: 50 / 394

•

YES, go to 40; NO, go to 41

•

40 - REPLACE THE REAR BRAKE SWITCH - END

•

41 - RESTORE THE CABLE HARNESS (GREEN CABLE) - END

•

42 - RESTORE THE CABLE HARNESS (YELLOW/GREEN CABLE) - END

•

44 - IS THERE VOLTAGE ON THE PINK/BROWN CABLE OF THE START-UP CONTROL

RELAY WHEN THE KEY IS SET TO ON AND THE FRONT OR REAR BRAKE SWITCH IS

PRESSED?

YES, go to 45; NO, go to 46

•

45 - IS THERE CONTINUITY ON THE PINK/BROWN CABLE FROM PIN 2 OF THE START-

UP CONTROL RELAY TO PIN 5 OF THE RETENTION RELAY AND FROM PIN 2 OF THE

START-UP CONTROL RELAY TO PIN 1 OF CONNECTOR B OF THE ECU?

YES, go to 19; NO, go to 47

•

46 - CHECK CONTINUITY BETWEEN PIN 1 AND PIN 2 OF THE RELAY AND CONTINU-

ITY AND GROUND INSULATION OF THE YELLOW/GREEN CABLE AND THE PINK/

BROWN CABLE - END

•

47 - RESTORE THE CABLE HARNESS(PINK/BROWN CABLE) - END

•

48 - RESTORE THE CABLE HARNESS(YELLOW/RED CABLE) - END

•

49 - IS THERE CONTINUITY BETWEEN THE STARTER BUTTON BLUE CABLE AND THE

GROUND LEAD?

YES, go to 50; NO, go to 51

•

50 - CHECK THE RIGHT LIGHT SWITCH CONNECTOR, THE CABLES FROM THE CON-

NECTOR TO THE LIGHT SWITCH AND THE LIGHT SWITCH - END

•

51 - RESTORE THE CABLE HARNESS (BLUE CABLE) - END

•

52 - DOES THE START-UP CONTROL RELAY WORK CORRECTLY?

•

YES, go to 53; NO, go to 54

•

53 - PROBABLE MALFUNCTION OF THE INJECTION ECU - END

•

54 - REPLACE THE RELAY - END 55 - DISCONNECT THE START-UP REMOTE CON-

TROL CONNECTOR, WHEN TRYING TO START UP THE ENGINE (BY PRESSING THE

STARTER BUTTON AND OPERATING THE BRAKES), IS VOLTAGE PRESENT ON THE

ORANGE/YELLOW CABLE?

YES, go to 56; NO, go to 58

•

56 - IS THERE CONTINUITY WITH THE GROUND OF THE BLUE CABLE OF THE START-

UP REMOTE CONTROL?

YES, go to 57; NO, go to 59

•

57 - REPLACE THE RELAY - END

•

58 - RESTORE THE CABLE HARNESS - END

Troubleshooting

MSS Mana GT ABS

TROUBL - 50

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды