APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 246

Страница: 246 / 394

- Fit the half-pulley on the bushing being careful

not to damage the top sealing ring.

- Make sure the pins and collar are not worn and

refit the pins and the collar.

- Using a curved-spout grease gun, lubricate the driven pulley assembly with approximately 10 grams

of grease. Apply the grease through one of the holes in the bushing until grease comes out through the

hole on the opposite side. This procedure is necessary to prevent the presence of grease beyond the

O-rings.

Recommended products

AGIP MP GREASE

Grease for bearings, joints, couplings and leverages

As an alternative to the recommended product, use top brand grease for roller bearings with an oper-

ating temperature range of -30°C...+140°C (-22°F...+284°F), a drop point of 150°C...230°C (302°F...

446°F), high corrosion protection qualities and good water and rust resistance.

Inspecting the clutch spring

- Measure the length of the movable driven half-

pulley spring, when unloaded.

Characteristic

Standard length:

190.2 mm

Limit allowed after use:

182 mm

Engine

MSS Mana GT ABS

ENG - 246

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды