APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 92

Страница: 92 / 394

REMOVAL

LOCATION ON THE VEHICLE:

on the fork, left

side, under the parking brake calliper support.

CONNECTOR LOCATION (if available):

under

the saddle, right side.

PINS

•

PIN 1- Ground connection (yellow)

•

PIN 2 - Power supply voltage/Output

signal (yellow/brown)

NAVIGATOR

Parameters:

Speed (km/h) - Vehicle speed.

ELECTRICAL ERRORS

Speed sensor

5DA0 electric malfunction:

Electrical fault in sensor or cable harness.

Troubleshooting:

Check the sensor connector and the ABS control unit connector. If they are not OK,

restore the connectors. If they are OK, check continuity of the yellow/brown cable between PIN 2 of the

sensor on the cable harness side and PIN 11 of the ABS control unit connector. If there is no continuity,

restore them. If there is, PIN 2 of the sensor on the cable harness side, with the sensor disconnected

and key set to ON, must have 12V voltage approximately: if there is no voltage, check PIN 2 for continuity

with the vehicle ground connection: if it is grounded, restore the cable harness. If OK, replace the control

unit. If PIN 2 has approx. 12 V, check continuity of the yellow cable between PIN 1 of the sensor on the

cable harness side and PIN 12 of the ABS control unit connector. If this is not OK, restore the cable

harness. If it is OK, replace the sensor.

LOGIC ERRORS

Speed sensor

5DA1 the signal works irregularly:

faulty sensor or signal interference.

Troubleshooting:

Check speed sensor retainer. If it is not OK, restore it. If it is OK, check if the tone

wheel is dirty, deformed or wrongly fixed. If any of this happens, replace the tone wheel. Otherwise,

replace the speed sensor.

5DA2 the signal decreases periodically:

Possible tone wheel fault due to deformations or dirt; pos-

sible alterations on the wheel bearing surface. In very rare cases, abnormal tone wheel vibrations.

Troubleshooting:

Check if the tone wheel is dirty, deformed or wrongly fixed. If the tone wheel is not

OK, replace it. If it is OK, check for possible faults in the wheel bearings and if it is not OK, replace the

bearings.

5DA3 no signal or speed measured too low in relation to the front wheel:

Faulty sensor or missing

sensor/tone wheel. Or excessive distance between the sensor and the tone wheel or tone wheel with

wrong number of teeth.

Electrical system

MSS Mana GT ABS

ELE SYS - 92

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды