manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 119

Belt replacement, Phase 2:

 Follow the procedure step by step as indicated in the various screen pages

(yellow or black label OBD module without 2006 legend).

Entering the gearshift stroke category:

 Allows you to enter the gearshift stroke category in case of

a new control unit (display of the category in the parameters screen page, see also Driving pulley

position sensor).

Gearshift stroke default value setting:

 Allows you to enter the default value for the gearshift stroke

category in the event of replacement of the variator components that affect the gearshift stroke. The

components are:

spacer

slider support

bearing support bushing

bearing support

fixed driving half-pulley

movable driving half-pulley

NEW CONTROL UNIT ACTIVATION PROCEDURE

It is necessary to replace also the belt and before the start-up, it is necessary to carry out the Potenti-

ometer reset procedure (driving pulley). It is also recommended to insert the Gearshift stroke category,

via the gearshift stroke category insertion adjustable parameter, read in the previous control unit (the

value is present in the control unit and on the half-pulley only from vehicles manufactured after February

2008). If you do not enter the Category, the control unit uses the default value.

CAUTION

FAILURE TO REPLACE THE BELT CAN SERIOUSLY DAMAGE THE SYSTEM SINCE THE NEW
CONTROL UNIT, TAKING FOR GRANTED THE BELT IS NEW, COULD MISJUDGE THE ACTUAL
WEAR AND CAUSE THE BELT TO BREAK.

GEARSHIFT STROKE CATEGORY UPDATE ON THE TRANSMISSION ECU

NOTE

THIS OPERATION MUST BE PERFORMED IF DURING ROUTINE OR EXTRAORDINARY MAIN-
TENANCE, THE GEARSHIFT STROKE CATEGORY SET IN THE TRANSMISSION ECU SHOULD
BE 0.

•

Check through the diagnosis instrument for any errors in the transmission ECU from the

"errors" menu. Erase them is necessary.

•

Take the measurement of the gearshift stroke to identify the category to which it belongs.

NOTE

THIS PROCEDURE IS ALSO VALID IN THE EVENT OF REPLACING THE TRANSMISSION ECU.

•

Perform the gearshift stroke category operations from the "settings" menu of the diagnosis

instrument.

CAUTION

MSS Mana GT ABS

Electrical system

ELE SYS - 119

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды