manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 94

Pin-out:

1. Negative signal

2. Positive signal

THE CONNECTION DIAGRAMS ARE IN THE ELECTRICAL SYSTEM SECTIONS; PAY ATTENTION

TO THESE DIAGRAMS AS THEY SHOW THE CONNECTOR/COMPONENT AS VIEWED FROM

THE CABLE HARNESS SIDE, THAT IS LOOKING AT THE CABLES WHEN GOING OUT OF THE

"MAIN" CABLE HARNESS AND INTO THE CONNECTOR/COMPONENT.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: FUEL INJECTION SYSTEM

PARAMETERS

Engine rpm

(rpm)

Engine revolutions per minute: the minimum value is set by the control unit and cannot be adjusted.

STATUSES

Synchronisation

Example value:

Synchronised / Not synchronised

It indicates if the control unit detects the revolution sensor signal correctly.

ELECTRICAL ERRORS

Engine revolution sensor P0335 -

 open circuit

Error cause:

•

An interruption in the sensor circuit has been detected, from PIN 25 to PIN 35 of connector

A (BROWN).

Troubleshooting:

•

Check the sensor connector and the injection control unit connector A (BROWN): if it is not

OK, restore; if it is OK, check continuity of the two cables: if there is no continuity, restore

the cable harness; if there is continuity, check the interruption on the sensor and replace it

CAUTION

IF THE ELECTRIC CIRCUIT IS SHORT-CIRCUITED, NO ERROR IS DISPLAYED. CHECK THE
SENSOR ELECTRICAL SPECIFICATIONS: IF IT IS NOT THE CORRECT ONE, REPLACE THE
SENSOR. IF IT IS THE CORRECT ONE, CHECK INSULATION FROM POWER AND GROUND
CONNECTION OF BOTH CABLES OF PINS 1 AND 2. PERFORM THE TESTS FROM THE SENSOR
CONNECTOR TO THE SENSOR. IF THEY ARE NOT OK, RESTORE THE CABLE HARNESS/RE-
PLACE THE SENSOR. IF OK, PERFORM THE TEST FROM PINS 25 AND 35 OF THE MARELLI
CONTROL UNIT ENGINE CONNECTOR A (BROWN) TO THE CABLE HARNESS AND REPLACE
THE LATTER.

Electrical system

MSS Mana GT ABS

ELE SYS - 94

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды