APRILIA MSS Mana GT ABS Скачать руководство пользователя

Страница: 244 / 394

- Remove the roller bearing with the specific tool,

supporting the fixed half-pulley with the bell.

Specific tooling

020376Y

Adapter handle

020375Y

28 x30 mm Punch

020483Y

30-mm guide

AP8140180

Extractor for bushings

Inspecting the driven fixed half-pulley

- Check that the belt contact surface is free from

wear.

- Measure the outside diameter of the pulley bush-

ing.

Characteristic

Minimum diameter allowed:

54.91 mm

Standard diameter:

55.00-0.015 -0.035 mm

Inspecting the driven sliding half-pulley

- Check that the belt contact surface is free from

wear.

- Remove the 2 inner sealing rings and the 2 ex-

ternal O-rings.

- Measure the inside diameter of the movable half-

pulley bushing.

Characteristic

Maximum diameter allowed:

55.05 mm

Standard diameter:

55.00 +0.035 0.00 mm

Engine

MSS Mana GT ABS

ENG - 244

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Похожие инструкции для MSS Mana GT ABS

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Похожие инструкции для MSS Mana GT ABS

Бренды по названию

Популярные бренды