APRILIA MSS Mana GT ABS Скачать руководство пользователя | Manualshive

Страница: 53 / 394

background image

•

11 - HAS THE INSTRUMENT PANEL BEEN REPLACED?

YES, go to 12; NO, go to 13.

•

12 - STORE ALL THE KEYS THE FIRST TIME THE INSTRUMENT PANEL IS SWITCHED

ON - END

•

13 - DELETE THE ERROR WITH THE "ERROR CLEARING" FUNCTION IN THE "DIAG-

NOSIS" FUNCTION OF THE INSTRUMENT PANEL - END

Belt

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

•

1 - WORD "BELT" SHOWN ON THE DISPLAY

•

2 - IS THE "EFI" WARNING LIGHT ON AND THE GEARSHIFT IN "AUTOMATIC - RAIN"

MODE?

YES, go to 4; NO, go to 3.

•

3 - NOW THE CURRENT BELT CAN BE USED UNTIL THE "EFI" WARNING LIGHT

COMES ON AND THERE IS A FORCED SETTING OF THE GEARSHIFT IN "AUTOMATIC

-RAIN" MODE

•

7 - HOWEVER, DO YOU WANT TO REPLACE THE BELT? YES, go to 5; NO, END

•

4 - CONNECT TO AXONE BY SELECTING "AUTOMATIC GEARSHIFT", THE "BELT

WEAR" ERROR, CODE 9011 CURR. (CURRENT) IS PRESENT.

•

5 - REPLACE THE BELT AND BEFORE STARTING THE ENGINE, REPLACE THE BELT

WITH AXONE (SEE ELECTRICAL SYSTEM/CHECKS AND CONTROLS/TRANSMISSION

ECU/ADJUSTABLE PARAMETERS).

•

6 - DELETE THE ERROR WITH THE "ERROR CLEARING" FUNCTION - END

GEAR

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

CAUTION

BEFORE ANY TROUBLESHOOTING, MAKE SURE THAT:
1) BATTERY VOLTAGE IS ABOVE 12V;
2) THE MAIN 30A FUSE IS NOT DAMAGED AND IS ADEQUATELY FITTED;
3) SECONDARY FUSES ARE NOT DAMAGED AND ARE ADEQUATELY FITTED.

1 - "EFI" WARNING LIGHT IS ON AND THE WORD "GEAR" IS SHOWN ON THE DISPLAY

2 - CONNECT TO AXONE BY SELECTING "AUTOMATIC GEARSHIFT" AND CHECK WHICH ER-

ROR IS PRESENT: FOR FURTHER INFORMATION ABOUT THE ERROR AND ITS POSSIBLE

CAUSES, PUSH BUTTON "?". THE AMBIENT PARAMETERS RELATED TO THE ERROR CAN ALSO

MSS Mana GT ABS

Troubleshooting

TROUBL - 53

«
...
51
52
53
54
55
...
»

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSS Mana GT ABS

Бренд: SCHUBERTH Страницы: 41

Stelvio 1200 MY11 2011

Бренд: MOTO GUZZI Страницы: 385

Бренд: SCA Страницы: 5

Easyrack 6612533 01 01

Бренд: hepco & becker Страницы: 5

Бренд: GAS GAS Страницы: 69

Бренд: Yamaha Страницы: 248

Бренд: Yamaha Страницы: 86

Бренд: TVS Страницы: 48

Бренд: DYNATEK Страницы: 8

Бренд: Barton Страницы: 35

Бренд: SUR-RON Страницы: 37

Бренд: MSA Страницы: 168

Бренд: CRATONI Страницы: 44

VarioProtect XXL-W TC AIR TH3

Бренд: schweisskraft Страницы: 28

Бренд: FMF Страницы: 4

Бренд: Yamaha Страницы: 91

Бренд: Yamaha Страницы: 117

Бренд: Yamaha Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды