manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 125

Potentiometer reset, Phase 2

Follow the procedure step by step as indicated in the different screen pages (yellow or black label OBD

module without 2006 legend).

Entering the gearshift stroke category

If the ECU is replaced, the gearshift stroke category can be entered in the new ECU (reading the

category in the old ECU). The categories range from 1 to 8.

Gearshift stroke default value setting:

Setting to be used if a component of the variator that affects the gearshift stroke has been replaced.

See also

Refitting the driving pulley

Driven pulley speed sensor

Function

To indicate the driven pulley speed by reading the

speed of rotation of the fixed half-pulley that has

four studs.

Operation / Operating principle

Inductive sensor: sinusoidal alternating current is

generated (approximately 0.7 V at idle speed) for

the transmission ECU reading.

Level in wiring diagram:

transmission manage-

ment

Location:

•

on the vehicle: on the crankcase cover,

driven pulley upper part.

•

under the fuel tank (within the protec-

tive rubber cap).

Electrical specifications:

 Coil resistance at Am-

bient temperature: 0.7 - 1.1 kOhm.

Pin-out:

1. Signal (cable colour not defined)

2. Ground (cable colour not defined)

3. Shielding

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

MSS Mana GT ABS

Electrical system

ELE SYS - 125

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды