manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 238

- Place the transmission cover on a wooden sur-

face and use the special tool so that it is adequate-

ly supported.

- Extract the bearing with the specific tool.

NOTE

BELL MUST BE PLACED INTO THE TRANSMISSION COV-
ER, CLOSE TO THE BEARING SEAT AND THE WOODEN
SURFACE, SINCE WITHOUT BELL THE ENTIRE COVER
STRUCTURE WOULD BEND; NOT ONLY IN THE AREA OF
MAXIMUM STURDINESS.

Specific tooling

AP8140180

 

Extractor for bushings

020376Y

 

Adapter handle

020357Y

 

32 x 35 mm adaptor

020363Y

 

20-mm Oil seal guide

Refitting the driven pulley shaft bearing

- Heat the transmission cover inside with a heat gun.

- Fit the bearing onto the special tool with a little grease to prevent it from coming out.

- Refit the new bearing with the specific tool.

Specific tooling

020376Y

 

Adapter handle

020359Y

 

42 x 47-mm adaptor

020363Y

 

20-mm Oil seal guide

- Refit the Seeger ring.

Engine

MSS Mana GT ABS

ENG - 238

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды