manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 214

- Hold the tip with one hand and the crankshaft with

the other, pull the crankshaft upwards.

- Pull out the tip from the bushings, remove the

crankshaft.

- Once the crankshaft has been removed it is possible to remove the timing chain on the transmission

side.

Inspecting the crankcase halves

- Before checking the crankcase halves, thoroughly clean all the surfaces and oil pipes.

- Clean the jets and contacts carefully.

NOTE

THE JET IS FED THROUGH THE MAIN BUSHINGS. PROPER OPERATION OF THIS COMPONENT
IMPROVES PISTON CROWN COOLING. CLOGGING HAS EFFECTS THAT ARE DIFFICULT TO
DETECT (PISTON TEMPERATURE INCREASE). FAILURE OR LEAKAGE CAN CONSIDERABLY
CAUSE A DROP IN LUBRICATION PRESSURE FOR THE MAIN BUSHINGS AND CONNECTING
ROD.

NOTE

AS ALREADY DESCRIBED IN THE LUBRICATION CHAPTER, IT IS ESPECIALLY IMPORTANT
THAT THE BY-PASS VALVE HOUSING SHOWS NO WEAR THAT MAY IMPAIR THE PROPER
SEALING OF THE LUBRICATION PRESSURE ADJUSTMENT PISTON. THE HEAD LUBRICATION

Engine

MSS Mana GT ABS

ENG - 214

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды