APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 207

Страница: 207 / 394

- Fit the pins and the rocking levers operating on

the transmission side.

- Lubricate the 2 rocking levers through the holes

at the top.

- Clean the camshaft by blowing short blasts of

compressed air, especially the groove that holds

the retaining plate.

- Lubricate the 2 bearings.

- Fit the camshaft in the cylinder head with the

cams opposing the rocking levers.

- Remove any LOCTITE left on the screws fixing the camshaft retaining bracket using a brush.

- Apply the recommended product to the fixing screws and tighten them to the prescribed torque.

Recommended products

Loctite 243

Medium strength threadlock

- Insert the camshaft retaining bracket so that the

countersinks are visible and tighten the 3 fixing

screws to the prescribed torque, being careful not

to damage the internal hexagon.

Locking torques (N*m)

Camshaft retaining bracket screws

4 ÷ 6

- Finish closing the flywheel side crankcase with the components following the instructions described

in the specific sections.

- Time following the instructions in the specific section.

MSS Mana GT ABS

Engine

ENG - 207

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды