APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 394

APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 52

•

8 - IS THERE VOLTAGE IN THE WHITE/RED CABLE?

YES, go to 9; NO, go to 12.

•

9 - SLIDE OFF THE AUXILIARY 15A FUSE: IS THERE VOLTAGE IN THE RED/BLACK

CABLE?

YES, go to 10; NO, go to 11.

•

10 - CHECK THE INSTRUMENT PANEL CONNECTOR AND CHECK IS THERE IS CON-

TINUITY IN THE GREEN CABLE FROM THE AUXILIARY FUSE TO PIN 1 OF THE

INSTRUMENT PANEL CONNECTOR - END

•

11 - CHECK CORRECT OPERATION OF RELAY 28 - END

•

12 - CHECK THE MAIN INJECTION RELAY CONNECTOR AND CHECK IF THERE IS

CONTINUITY IN THE WHITE/RED CABLE FROM THE 30A FUSE TO THE MAIN INJEC-

TION RELAY CONNECTOR - END

Service

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

•

1 - "EFI" WARNING LIGHT IS ON AND THE WORD "SERVICE" IS SHOWN ON THE DIS-

PLAY

•

2 - CONNECT TO AXONE SELECTING "PETROL INJECTION": ARE THERE ANY CUR-

RENT ERRORS?

YES, go to 3; NO, go to 9.

•

3 - FIND THE MALFUNCTION (SEE "ELECTRICAL SYSTEM/CHECKS AND CONTROLS"

CHAPTER AND RESTORE THE CORRECT OPERATION.

•

4 - HAS THE INJECTION ECU BEEN REPLACED? YES, go to 5; NO, go to 6.

•

5 - WITH AXONE SELECT "THROTTLE POSITIONER AUTODETECTION" - END

•

6 - HAS THE THROTTLE POSITIONER BEEN REPLACED?

YES, go to 7; NO, go to 8.

•

7 - WITH AXONE SELECT THROTTLE POSITIONER AUTODETECTION

•

8 - DELETE THE ERROR WITH THE ERROR CLEARING FUNCTION IN THE DEVICES

ACTIVATION (INJECTOR ICON) SCREEN PAGE - END

•

9 - OPEN THE "DIAGNOSIS" FUNCTION OF THE INSTRUMENT PANEL AND SELECT

"INSTRUMENT PANEL ERRORS"

•

10 - FIND THE MALFUNCTION (SEE THE ELECTRICAL SYSTEM/CHECKS AND CON-

TROLS/INSTRUMENT PANEL/DIAGNOSIS CHAPTER) AND RESTORE THE CORRECT

OPERATION.

Troubleshooting

MSS Mana GT ABS

TROUBL - 52

«
...
50
51
52
53
54
...
»

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды