manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 77

81.HEATED HANDGRIP UNIT

CAUTION

THE ELECTRICAL SYSTEM IN THIS VEHICLE CAN BE SLIGHTLY DIFFERENT, DEPENDING ON
THE SERIAL NUMBER, SPECIFICALLY IN THE LAYOUT OF THE GLOVE-BOX LIGHT SWITCH
CONNECTIONS.
THE DIFFERENCES ARE HIGHLIGHTED ON THE DIAGRAM BY TWO TYPES OF LINES, DIFFER-
ENT AND ALTERNATE BETWEEN THEM:

•

IF THERE IS A WHITE/RED CABLE ON THE VEHICLE, REFER TO THE PATH MARKED
WITH long/short dashes

•

IF THERE IS A GREEN CABLE ON THE VEHICLE, REFER TO THE PATH MARKED WITH
A UNIFORM DOTTED LINE.

Checks and inspections

GENERAL CONCEPTS OF ELECTRICAL TROUBLESHOOTING

THE CONNECTION DIAGRAMS ARE IN THE ELECTRICAL SYSTEM SECTIONS; PAY ATTENTION

TO THESE DIAGRAMS AS THEY SHOW THE CONNECTOR/COMPONENT AS VIEWED FROM

THE CABLE HARNESS SIDE, THAT IS LOOKING AT THE CABLES WHEN GOING OUT OF THE

"MAIN" CABLE HARNESS AND INTO THE CONNECTOR/COMPONENT.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING PROCEDURE ON THE VEHICLE, CHECK
THAT THE BATTERY VOLTAGE IS ABOVE 12V.

CONNECTOR CHECK PROCEDURE

The procedure includes the following checks:

1. Observation and check of the connector correct

position on the component or on the coupling con-

nector, making sure that the locking catch is re-

leased.

2. Observation of the terminals on the connector:

no rust marks or dirt should be present and it is

important to check terminal correct positioning on

the connector (i.e., all terminals aligned at the

same depth) and terminal integrity (i.e., that termi-

nals are not loose, open/bent, etc.). For connec-

tors whose terminals are not visible (e.g. Marelli

control unit) use a metal cable of suitable diameter

and introduce it carefully in the connector slot at

the same depth as for the other terminals of the

connector.

CAUTION

IN CASE OF TEMPORAL MALFUNCTIONING, CARRY OUT
ALL DUE CHECKS LOOKING FOR FAULT BY MOVING
SLIGHTLY THE CABLE HARNESS BEING INSPECTED.

MSS Mana GT ABS

Electrical system

ELE SYS - 77

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды