manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 115

•

connector: right side, under helmet

compartment, along upper frame.

Electrical characteristics:

•

STOP position: the circuit is open

•

RUN position: closed circuit (continui-

ty)

Pin-out:

1. Green/orange cable: ground connection

2. Yellow/grey cable: voltage 12V

THE CONNECTION DIAGRAMS ARE IN THE ELECTRICAL SYSTEM SECTIONS; PAY ATTENTION

TO THESE DIAGRAMS AS THEY SHOW THE CONNECTOR/COMPONENT AS VIEWED FROM

THE CABLE HARNESS SIDE, THAT IS LOOKING AT THE CABLES WHEN GOING OUT OF THE

"MAIN" CABLE HARNESS AND INTO THE CONNECTOR/COMPONENT.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: FUEL INJECTION SYSTEM

STATUSES

Run / stop switch

Example value

:Run/Stop

Troubleshooting

•

Indication on Axone always STOP: disconnect the connector and, with the switch set to

RUN, check if there is continuity towards the switch of the two cables- yellow/grey and green/

orange: if there is not continuity, replace the sensor; if there is, check the connector. If it is

not OK, restore the cable harness; if it is OK, with key set to KEY ON, check if there is voltage

on the yellow/grey cable: if there is no voltage, restore the cable harness; if there is, check

the yellow/grey cable earth insulation: if there is continuity to ground, restore the cable har-

ness; if it is OK, take the key to KEY OFF and check the control unit connector and the

continuity of the yellow/grey cable between the connector in question and PIN 27 of the

control unit connector B "BLUE": if not OK, restore the cable harness; if OK, replace the

Marelli control unit.

•

Indication on Axone always RUN: disconnect the connector and, with the switch set to

STOP, check if there is continuity between the two cables of the switch: if there is continuity,

replace the switch; if there is not, it means that, with key set to KEY ON, the green/orange

cable is shorted to positive: restore the cable harness.

MSS Mana GT ABS

Electrical system

ELE SYS - 115

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды