APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 194

Страница: 194 / 394

AP8140595

Axone + battery charger (230V 50Hz)

AP8202311

Axone + battery charger (110V 60Hz)

If the values do not correspond, check:

- distribution timing

- rpm timing sensor

- injection control unit

Timing

- With the TORX wrench, remove the timing check

cap.

- With the references aligned, operate on the driv-

ing pulley to turn the crankshaft until on the fly-

wheel the rear cylinder timing reference mark «

is aligned to the crankcase reference, correspond-

ing to the rear piston top dead centre.

- Fit the tone wheel and the timing system gear

with the chain and align the reference marks.

Engine

MSS Mana GT ABS

ENG - 194

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды