manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 21

THE REAR CYLINDER PISTON, UNLIKE THE FRONT ONE, MUST BE FITTED WITH THE ARROW
TURNED TOWARDS THE EXHAUST.
THE PISTON RINGS MUST BE FITTED WITH THE "TOP" REFERENCE OR THE TRADEMARK
FACING UP.

Rod small end - pin - piston

ROD SMALL END - PIN COUPLING CLEAR-

ANCE

- Calculate the rod small end - pin coupling clear-

ance.

Characteristic

Standard clearance:

0.015 - 0.029 mm

PIN - PISTON COUPLING CLEARANCE

- Calculate the pin - piston coupling clearance.

NOTE

THE PIN HOUSINGS HAVE TWO LUBRICATION CHAN-
NELS FOR THIS REASON MEASURE THE DIAMETER AC-
CORDING TO THE PISTON AXIS

Characteristic

Standard clearance:

0.001 - 0.010 mm

PISTON BEARINGS DIAMETER

- Measure the diameter of the bearings on the piston.

Characteristic

Standard diameter:

22 + 0.006 +0.001 mm

MSS Mana GT ABS

Characteristics

CHAR - 21

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды