manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 257

CAUTION

IN THE EVENT OF REPLACEMENT OF ONE OR MORE OF THE FOLLOWING COMPONENTS:

•

SPACER (DIAM. 40 mm, LENGTH 50.5 mm)

•

SLIDER SUPPORT

•

BEARING SUPPORT (SLIDING) BUSHING

•

BEARING SUPPORT

•

FIXED DRIVING HALF-PULLEY

•

MOVABLE DRIVING HALF-PULLEY

1) TO PREVENT THE RISK OF THE VARIATOR LOCKING IN SEVENTH GEAR, IN THE TRANS-
MISSION ECU SET THE "DEFAULT" VALUE OF THE GEARSHIFT STROKE AS SHOWN IN THE
CHAPTER "ELECTRICAL SYSTEM/CHECK AND CONTROLS/DRIVE PULLEY POSITION SEN-
SOR/ADJUSTABLE PARAMETERS".
2) NEVER TURN THE KEY TO ON BEFORE COMPLETING THE FITTING OF THE UNIT AND CON-
NECTING WITH THE DIAGNOSIS INSTRUMENT.
3) PERFORM THE POTENTIOMETER RESET PROCEDURE BY CONNECTING THE DIAGNOSIS
INSTRUMENT AND ENTERING INTO MANAGING "AUTOMATIC TRANSMISSION/AUTODIA/PO-
TENTIOMETER RESET/ADJUST".
4) PERFORM THE GEARSHIFT STROKE CATEGORY INSERTION PROCEDURE FROM THE
"SETTINGS" MENU OF THE DIAGNOSIS INSTRUMENT. PERFORM A KEY OFF/ON TO STORE
THE DATA.
5) CHECK THAT THE GEARSHIFT STROKE CATEGORY HAS BEEN STORED CORRECTLY
FROM THE DIAGNOSIS INSTRUMENT MENU.

PROCEDURE FOR MEASURING THE GEAR-

SHIFT CLASS

•

Insert the advancement bushing into

the hole, taking care that the teeth en-

gage with the slider supports and the

grooves of the advancement bushing

itself.

•

Position and tighten the pulley control

bushing to the end of stroke.

MSS Mana GT ABS

Engine

ENG - 257

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды