APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 19

Страница: 19 / 394

ADDLE

Name

Torque in Nm

hex headflanged screw fixing saddle rotation bracket - M6x20

(2)

10 Nm (7.38 lbf ft)

Countersunk head, self-tapping screw fixing saddle hinges to

saddle bottom - 5 (4)

1.5 Nm (1.11 lbf ft)

Driver saddle rear hex headflanged fixing screw - M6x20 (2)

10 Nm (7.38 lbf ft)

Driver saddle lateral TCB fixing screw - 4.2x16 (2)

1 Nm (0.74 lbf ft)

RONT

BODYWORK

Name

Torque in Nm

Front mudguard TBEI fixing screw - M5x12 (4)

6 Nm (4.42 lbf ft)

Right/left SWP crosshead flanged screw fixing helmet com-

partment - M5x20 (9)

1.5 Nm (1.11 lbf ft)

Battery cover TBEI fixing screw - M5x12 (2)

6 Nm (4.42 lbf ft)

Screw fixing shock absorber to helmet compartment - M6x20

(1)

10 Nm (7.38 lbf ft)

Self-locking M8 nut fixing shock absorber to helmet compart-

ment (1)

25 Nm (18.44 lbf ft)

Door switch TCB fixing screw - 3.9x14 (1)

1 Nm (0.74 lbf ft)

Lock TBEI fixing screw - M6x16 (2)

10 Nm (7.38 lbf ft)

Self-locking M6 nut fixing injection ECU to support (2)

10 Nm (7.38 lbf ft)

hex headflanged screw fixing cable harness ground cable on

injection ECU - M6x12 (2)

10 Nm (7.38 lbf ft)

Self-tapping screw fixing ECU support to compartment - 4.2x12

(2)

1 Nm (0.74 lbf ft)

hex headflanged screw fixing helmet compartment to chassis

- M6x20 (4)

10 Nm (7.38 lbf ft)

Right air deflector TBEI flanged fixing screw - M5x12 (2)

6 Nm (4.42 lbf ft)

TBEI flanged screw fixing right air deflector to expansion tank

- M5x9 (1)

4 Nm (2.95 lbf ft)

Left air deflector TBEI flanged fixing screw - M5x12 (3)

6 Nm (4.42 lbf ft)

Fairing TBEI flanged fixing screw - M5x12 (10)

6 Nm (4.42 lbf ft)

Steering lock housing TBEI fixing screw - M6x30 (2)

6 Nm (4.42 lbf ft)

Latch support TCB fixing screw - 4.2x16 (2)

1 Nm (0.74 lbf ft)

Stainless steel self-tapping screw for plast. fixing helmet com-

partment (14)

1 Nm (0.74 lbf ft)

Rear cover TBEI fixing screw - M5x12 (2)

6 Nm (4.42 lbf ft)

Rear cover TCB fixing screw - 4.2x16 (2)

1 Nm (0.74 lbf ft)

TBEI screw with front washer for fixing the instrument panel to

the side and top fairing elemnts M5x12 (6)

6 Nm (4.42 lbf ft)

Self-tapping screw to fix the instrument panel to the panel -

Diam.5x14 (3)

3 Nm (2.21 lbf ft)

TBEI screw for fixing the steering lock protection to the helmet

compartment - M6x35 (2)

10 Nm (7.38 lbf ft)

Allen screw for fixing the turn indicator to the side fairing -

M6x16 (1)

1.5 Nm (1.11 lbf ft)

TBEI screw with front washer for fixing the air deflector to the

helmet compartment and top fairing elements to the shield -

M5x12 (2)

6 Nm (4.42 lbf ft)

Screw for fixing top fairing element, air deflector and deflector

to the side fairing - Diam.3.9x10 (9)

1 Nm (0.74 lbf ft)

Allen screw for fixing the turn indicator to the side fairing -

M6x16 (1)

1.5 Nm (1.11 lbf ft)

TBEI screw for fixing the air deflector to the helmet compart-

ment and top fairing elements to the shield - M5x12 (2)

6 Nm (4.42 lbf ft)

Screw for fixing top faring element air deflector and deflector to

the side fairing - Diam.3.9x10 (9)

1 Nm (0.74 lbf ft)

TBEI screw with front washer for fixing the shield to the side

fairings - M6x25 (2)

10 Nm (7.37 lbf ft)

Screw for fixing the shield and lamp mounting to the front frame

- M6x25 (2)

10 Nm (7.37 lbf ft)

Screw to fix the front cover to the shield - Diam.5x14 (2)

3 Nm (2.21 lbf ft)

Screw to fix the lamp to the lamp mounting - 3.9x14 (4)

1 Nm (0.74 lbf ft)

MSS Mana GT ABS

Characteristics

CHAR - 19

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды