APRILIA MSS Mana GT ABS Скачать руководство пользователя | Manualshive

Страница: 42 / 394

background image

The gap between the electrodes should be be-

tween 0.7 - 0.8 mm (0.027 - 0.031 in). Otherwise,

replace the spark plug (2).

•

Make sure the washer is in good con-

ditions.

Installation:

•

Once the washer is fitted, screw the

spark plug (2) carefully to avoid dam-

aging the thread.

•

Tighten using the spanner supplied in

the tool kit. Make each spark plug (2)

complete 1/2 of a turn to compress the

washer.

CAUTION

IT IS ESSENTIAL TO TIGHTEN THE SPARK PLUG (2)
PROPERLY. A LOOSE SPARK PLUG MAY CAUSE ENGINE
OVERHEATING AND RESULT IN SEVERE DAMAGE.

Locking torques (N*m)

Spark plug (2)

13 Nm (9.59 lbf ft)

Engine oil

Check

Check the engine oil level frequently.

NOTE

CARRY OUT MAINTENANCE OPERATIONS AT HALF THE
INTERVALS SPECIFIED IF THE VEHICLE IS USED IN PAR-
TICULAR RAINY OR DUSTY CONDITIONS, OFF ROAD OR
FOR TRACK USE.

CAUTION

CHECK ENGINE OIL LEVEL WHEN THE ENGINE IS WARM,
WITH THE VEHICLE PERFECTLY UPRIGHT, WITH BOTH
WHEELS ON THE GROUND, ON A SOLID AND LEVEL SUR-
FACE.

NOTE

DO NOT LET THE ENGINE IDLE WHEN THE VEHICLE IS AT
STANDSTILL TO WARM UP THE ENGINE AND OBTAIN
THE OPERATING TEMPERATURE OF ENGINE OIL.
OIL IS BEST CHECKED AFTER A TRIP OR AFTER TRAV-
ELLING APPROXIMATELY 15 km (10 mi), OUT OF TOWN
(ENOUGH TO WARM UP ENGINE OIL TO OPERATING
TEMPERATURE).
IT IS IMPORTANT TO MEASURE THE ENGINE OIL MINI-
MUM LEVEL USING THE DIPSTICK (1), AND THE ENGINE
OIL MAXIMUM LEVEL THROUGH THE CRANKCASE
SIGHT GLASS (2).

Maintenance

MSS Mana GT ABS

MAIN - 42

«
...
40
41
42
43
44
...
»

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSS Mana GT ABS

Бренд: yasuni Страницы: 8

Бренд: HYOSUNG Страницы: 98

Бренд: Graphite Страницы: 44

Бренд: Suzuki Страницы: 230

Бренд: Sicor Страницы: 2

Бренд: GYS Страницы: 36

GT650SR - PARTS CATALOGUE

Бренд: HYOSUNG Страницы: 124

Бренд: SHOEI Страницы: 38

R 1200 R Classic

Бренд: BMW Страницы: 1

Бренд: Yamaha Страницы: 9

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 91

Бренд: Yamaha Страницы: 92

Virago XV250 2004

Бренд: Yamaha Страницы: 95

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды