APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 340

Страница: 340 / 394

•

Repeat this procedure until the brake fluid is clear and has no air bubbles. (about 10 to 20

times).

NOTE: CHECK BRAKE FLUID LEVEL IN THE RESERVOIR AND, IF NECESSARY, TOP UP

(CHECKING BRAKE PAD WEAR).

•

Bleed as previously described, also on the bleed valve installed on the front brake pump.

•

Then perform the same procedure for the rear brake calliper, acting only on the valve in-

stalled on that calliper.

•

Fill the reservoir until it reaches the reference "MAX" and refit the cap (check pad wear).

•

Detach the bleed hoses and close the bleed screws again to the correct tightening torque.

•

Check the stroke and the sensitivity of both the lever and the brake pedal.

NOTE: IF AFTER BLEEDING, THE STROKE OF THE PEDAL OR THE LEVER IS TOO LONG,

CHECK THAT THERE ARE NO LEAKS IN THE BRAKING SYSTEM AND IF EVERYTHING IS OK,

CONTINUE BLEEDING OPERATIONS USING AXONE.

BRAKE BLEEDING AFTER ABS CONTROL

UNIT REPLACEMENT

VEHICLE PREPARATION

•

Connect the bleed bottle to the bleed

screws of the front and rear callipers

and open it.

•

Fully press down the lever and the

brake pedal and fix them into position

with the respective locking devices.

•

Close the bleed screws of the front and

rear callipers and remove the bleed

bottle.

•

Remove the damaged ABS control

unit.

Note: First of all, detach the brake pipes that

go from the ABS control unit to the brake pump

(1-4) and immediately seal the opened unions

of the ABS control unit with protective caps.

Afterwards, remove pipes (2-3) that go from the

ABS control unit to the brakes and also seal

these unions with protective caps.

•

Install the new ABS control unit, previ-

ously filled up.

Braking system

MSS Mana GT ABS

BRAK SYS - 340

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды