YOKOGAWA SL1400 ScopeCorder LITE User Manual Download Page 64

Page: 64 / 589

2-33

IM 701240-01E

App

Index

Explanation of Functions

Display Interpolation «For procedures, see section 8.2.»

In areas where less than 1000 points of data exist in the 10 divisions along the time axis

(referred to as interpolation areas), a continuous waveform cannot be displayed because

there is not enough sampled points. In this case, waveform is displayed by interpolating

between data points. You can select the interpolation method from the following:

Linear Interpolation

Linearly interpolates between two points.

Sine Interpolation

sin x

Generates interpolation data using the function sin(x)/x then interpolates between

two dots using the resulting sine curve. Sine interpolation is suitable for observing sine

waves or similar waves.

Interpolation OFF

Displays discrete dots without performing interpolation.

Linear Interpolation

Sine Interpolation

Interpolation OFF

If the interpolation is OFF, waveforms are displayed using dots. In this setting, up to

100100 points (100 kpoints) of the acquired data are displayed without using P-P

compression (page 2-4). For details, see page 2-5.

Graticule «For procedures, see section 8.3.»

You can change the type of graticule that is displayed to suit your needs. For example,

you can show a grid on the screen or show only the frame.

Accumulated Display «For procedures, see section 8.4.»

This mode holds each waveform on the screen for a time that is longer than the update

cycle, so that newer waveforms appear overlapped on older waveforms. If you select

Persist, the waveforms are accumulated.

Accumulated display is useful when you want to observe jitters and temporary turbulence

in waveforms. Accumulated display is also possible on waveforms that are recalled using

the history memory function.

2.4 Setting Waveform Acquisition Conditions and Display Conditions

Summary of Contents for SL1400 ScopeCorder LITE














































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SL1400 ScopeCorder LITE

Reviews:

Related manuals for SL1400 ScopeCorder LITE

Brands by name

Popular brands

YOKOGAWA SL1400 ScopeCorder LITE, User Manual

Search results

Summary of Contents for SL1400 ScopeCorder LITE

Reviews:

Related manuals for SL1400 ScopeCorder LITE

Brands by name

Popular brands