file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_5g1.htm
same on all fileservers and the Print Server password must be the same on all fileservers.
Note regarding NetWare 4 (bindery): You can set up the printer on the NetWare 4 Server by performing
the following steps:
1. Create a Bindery Queue
2. Create a Bindery Print Server Name
3. Assign Print Server to Queue.
4. Access Quick setup and change Printer Location from Manual Load to Auto Load (Local).
6. Continue following setup instructions for Internet Services.
Configure NetWare Settings using Internet Services
1.
Open your Web browser and enter the TCP/IP address of the Printer in the Address or Location field.
Press
Enter
.
2.
Click the
Properties
button or Tab.
3.
Click the plus symbol (+) to the left of the
Protocol Settings
file folder.
4.
Select
NetWare
in the directory tree.
5.
The available selections include:
A Host Name (Print Server) Text box. Use this name in the Server setup of the Print
Server using PCONSOLE.
A Mode selection box for Directory (NDS) or Bindery.
A Primary File Server name entry box (Bindery).
A Language Selection box (Japanese or English).
An Entry box for Queue Polling Interval (1 - 1000 seconds).
An Entry box for SAP frequency (1 - 100 seconds, with the ability to set to zero, which is
off).
Two Password text boxes for logging into the NetWare Server.
Under the NDS Subject Label there is a text box for NDS Tree, followed by one for NDS
Context.
A Frame Selection box, with a default of Auto sensing. Other selections include Ethernet
II (used when running TCP/IP on your network), Ethernet 802.3 (used for NetWare
versions up to 3.11), Ethernet 802.2 (the default for NetWare 3.12 and later), and
Ethernet SNAP (used on networks running TCP/IP and/or AppleTalk).
A display of the Printer's Network (MAC) address.
A Service Location Protocol Enablement box. For use with NetWare 5 and newer
versions, this protocol helps to reduce service advertising network traffic.
6.
Either accept the default Print Server Name or type in a new name that matches the name used on the
Server.
7.
Select Bindery as your network Mode.
8.
Provide the name of the Primary Server.
9.
Enter in a polling rate for
Queue
Polling Interval
.
10.
Enter in a SAP (service advertising protocol) frequency, or set
SAP frequency
to zero (off).
11.
Type a
Password
for the Printer to log into the NetWare Server, and type it a second time for
confirmation.
12.
For Frame Selection, if in doubt, leave the setting at its Auto sensing default value.
13.
Click the
Apply New Settings
button, then click the
Reboot button
to reboot the Printer and apply
setting changes.
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_5g1.htm (2 of 3) [9/4/03 8:32:50 AM]
Summary of Contents for WorkCentre M24 Color
