Xerox WorkCentre M24 Color System Administrator Manual Download Page 151

Page: 151 / 228

Group Dial

Group Dial

FP5

Fax (Phone)

Press the

Access

button to enter System Administration Mode.

On the keypad enter [11111] or current password. Touch

Confirm

when finished.

Touch

System Settings

Touch

Setup Menu

Touch

Group Send

Select a Group number, using the keypad.

Touch

Create/Delete

Use the numeric keypad enter the three-digit Address Number, touch

Add

When complete, touch

Save

10.

Touch

Close

until the System Settings screen is displayed.

Click

to continue on to Comment:

file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/Pages/fp5-group-dial.htm [9/4/03 8:33:07 AM]

Summary of Contents for WorkCentre M24 Color





































































































































































































































Search results

Summary of Contents for WorkCentre M24 Color

Reviews:

Related manuals for WorkCentre M24 Color

Brands by name

Popular brands

Xerox WorkCentre M24 Color, System Administrator Manual

Search results

Summary of Contents for WorkCentre M24 Color

Reviews:

Related manuals for WorkCentre M24 Color

Brands by name

Popular brands