file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_5g1.htm
Step 5 ...continued
Novell NetWare 3.1x (Bindery) Networks
Enable the NetWare Port at the Printer
1.
Press the rectangular
Access button
on the Printer Control Panel, located directly above and slightly to
the right of the numeric keypad.
2.
Press the
"1" key
on the numeric keypad five consecutive times. (This is the factory default
"password.")
3.
Press the rectangular
Confirm button
on the touch screen.
4.
Press the
System Settings button
(the right-hand button of the two buttons displayed on the touch
screen). Note: If you press the left button by mistake, the Main menu will be displayed and you will have
to start over at step one above.
5.
Press the
System Settings button
(the top left button displayed on screen).
6.
Press the
Network Settings button
(the top right button displayed on screen).
7.
Press the
Port Settings button
(the left-hand button) to access the Port Settings Menu. Note: If you
press the right-hand button by mistake, you will be in the Protocol Settings Menu and will have to press
the Close button to return to the two-button selection screen.
8.
Press the
NetWare
selection line on the Port Settings Menu screen.
9.
Press the
Change Settings button
in the lower right corner of the Port Settings Menu screen.
10.
When the NetWare Port Selection Menu displays, note that you have only one selection on a single,
numbered horizontal line. Press this selection labeled
Port Status
.
11.
Press the
Change Settings
button.
12.
On the Settings screen, note which of the two square buttons is highlighted as the current setting for
NetWare Port Enablement. The available settings are Enabled or Disabled. To enable NetWare at the
Printer, select the Enabled setting.
13.
Press the
Save
button (upper right-hand button) on the touch screen, which returns you to the NetWare
Port Selection Menu.
14.
Exit the NetWare Port Selection Menu and return to the Port Settings Menu by pressing the rectangular
Close
button in the upper right corner of the touch screen.
15.
Exit the Port Settings Menu by pressing the rectangular
Close
button in the upper right corner of the
Port Settings Menu screen.
16.
Exit the Ports and Protocols selection screen by pressing the rectangular
Close
button in the upper
right corner of the screen.
17.
Exit the screen containing the Network Settings button by pressing the rectangular
Close
button in the
upper right corner of the screen.
18.
Finally, press the rectangular
Exit
button in the upper right corner of the four-button, System Settings
screen to have the printer reboot and enable your NetWare setting.
Set Up a Print Server, Queue, and Name on the Primary Server
1.
Set up a Print Server, Queue, and Printer Configuration on the Primary Server using PCONSOLE.
Refer to the documentation supplied by Novell (
www.novell.com
) to complete this task.
Note: Record precisely (observe upper and lower case, punctuation etc.) the following: the
Primary
Server name, Frame type
used
, Print Server name, Print Server password,
and the
Queue name
assigned. If your printer services queues on multiple fileservers, the Print Server name must be the
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_5g1.htm (1 of 3) [9/4/03 8:32:50 AM]
Summary of Contents for WorkCentre M24 Color
