Microsoft (NetBIOS over IP) Networks
Microsoft (NetBIOS over IP) Networks
B6
Before You Start
1.
Print a
Settings List
as stated under the
Network Connectivity Tab
of this guide.
2.
Referring to the Settings List,
verify that "SMB" is enabled
. To enable "SMB" at the Printer, if
required, follow the procedure below.
3.
Referring to the Settings List,
verify that DNS (or WINS
, if using only a Windows NT network)
is
enabled
. The use of Naming Servers is REQUIRED to resolve NetBIOS device names to IP addresses
for packet routing over the TCP/IP network.
4.
To enable the Printer to communicate with the Naming Servers, refer to the instructions supplied under
the selection "TCP/IP Dynamic Addressing", located in the
NOS Selection
menu, under the
Network
Connectivity Tab
of this guide.
5.
When using WINS or DNS, be sure to refer to the Server Operating System documentation for the
appropriate procedure to use to enable NetBIOS name to IP address resolution on the Server.
Enabling the SMB Setting at the Printer, if required
1.
Press the rectangular
Access button
on the Printer Control Panel, located directly above and slightly to
the right of the numeric keypad.
2.
Press the
"1" key
on the numeric keypad five consecutive times. (This is the factory default
"password.")
3.
Press the rectangular
Confirm button
on the touch screen.
4.
Press the
System Settings button
(the right-hand button of the two buttons displayed on the touch
screen). Note: If you press the left button by mistake, the Main menu will be displayed and you will have
to start over at step one above.
5.
Press the
System Settings button
(the top left button displayed on screen).
6.
Press the
Network Settings button
(the top right button displayed on screen).
7.
Press the
Port Settings button
(the left-hand button) to access the Port Settings Menu display. Note: If
you press the right-hand button by mistake, you will be in the Protocol Settings Menu and will have to
press the Close button to return to the two-button selection screen.
8.
When the Port Settings menu displays, press the
SMB
selection line.
9.
Press the
Change Settings button
in the lower right corner of the Port Settings Menu screen.
10.
When the SMB Selection Menu displays, note that you have only one setting selection on a single,
numbered horizontal line. Press this selection line.
11.
Press the
Change Settings
button.
12.
On the Settings screen, note which of the two square buttons is highlighted as the current setting for
SMB Enablement. The available settings are Enabled or Disabled. To enable SMB at the printer, select
the
Enabled
setting.
13.
Click the
Save
button on the touch screen, which returns you to the SMB Selection menu. (To exit the
Settings screen, without making changes, click the Cancel button.)
14.
Exit the SMB Selection Menu and return to the Port Settings Menu by pressing the rectangular
Close
button in the upper right corner of the touch screen.
15.
Exit the Port Settings Menu by pressing the rectangular
Close
button in the upper right corner of the
Ports Menu screen.
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/Pages/B6_NetBIOS.htm (1 of 3) [9/4/03 8:32:34 AM]
Summary of Contents for WorkCentre M24 Color
