Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download Page 68

Page: 68 / 503

Phaser 5400 Laser Printer Service Guide

Duplex Jam
Open Rear Cover
Clear Paper Path

E7-1

E7: Duplex Jam

1. Duplex Sensor is not actuated within

the time after the start of the Duplex

drive motor in reverse.

2. Duplex Sensor is being actuated at

Power-Up.

3. Duplex Sensor is on when the

interlock is closed.

Open the Rear Cover
and remove any paper.
Go to RAP 20,

page 82

Stacker Jam
Open Rear Cover
Open Stacker
Door
Clear Paper Path

E8-1

E8-1 HCS Jam

1. HCS Sensor did not actuate within

time after the actutation of the Exit

sensor.

2. HCS Sensor is not deactuated

within time after actuation of HCS

Sensor.

3. HCS Sensor is actuated at power

on.

Comment:

Jam in the HCS

Open HCS rear door
and remove any paper.
Open Rear cover and
remove any paper.
Go to RAP 21,

page 84

Duplex Unit Fail
or Removed

E9-1

E9: Duplex Fail

Duplex module removed while power
is on.

Reinstall Duplex
Module
Go to RAP 22,

page 86

Stacker Bin Fail
Power Off/On

E9-2

E-9:

HCS removed while power is on.

Reinstall HCS
Go to RAP 23,

page 88

Tray 2 Failure
Power Off/On

E9-3

E-9: HCF Fail

2000-Sheet Feeder removed while
power is on.

Comment:

2000-Sheet Feeder

installed as Tray 2.

Reinstall HCF
Go to RAP 24,

page 89

Tray 3 Failure
Power Off/On

E9-3

E-9: HCF Fail

2000-Sheet Feeder removed while
power is on.

Comment:

2000-Sheet Feeder

installed as Tray 3.

Reinstall HCF
Go to RAP 24,

page 89

Install
Print Cartridge

J3: EP Cartridge

Print Cartridge is not installed.

Install the Print
Cartridge, or replace
with the correct Print
Cartridge.
Go to RAP 27,

page 92

Table 18

Error Code / Repair Analysis Procedure (cont'd.)

Displayed

Error Message

Fault

History
Log

Diagnostic Message /

Fault Description /
Comment

Action

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Search results

Summary of Contents for 5400N - Phaser B/W Laser Printer

Reviews:

Brands by name

Popular brands

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Search results

Summary of Contents for 5400N - Phaser B/W Laser Printer

Reviews:

Brands by name

Popular brands