Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download

Page: 392 / 503

Phaser 5400 Laser Printer Service Guide

363

RRP 12.11 Casters

(See

PL 12.2 2000-Sheet Feeder (2 of 4)

)

Removal

Warning: Switch off the power and disconnect the Power Cord.

Remove the Printer / 500-Sheet Feeder (RRP 11.1 500-Sheet Feeder Removal).

Remove the Left Foot.

Remove the Left Side Cover (RRP 12.2 Left Side Cover).

Remove all paper from the 2000-Sheet Feeder tray.

Tilt the 2000-Sheet Feeder onto its left side.

Note:

The front casters are locking casters and rear are not.

Remove the three screws that secure the defective caster.

Replacement

Reinstall the components in the reverse order.

Figure 153 Casters

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Search results

Summary of Contents for 5400N - Phaser B/W Laser Printer

Reviews:

Related manuals for 5400N - Phaser B/W Laser Printer

Brands by name

Popular brands

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Search results

Summary of Contents for 5400N - Phaser B/W Laser Printer

Reviews:

Related manuals for 5400N - Phaser B/W Laser Printer

Brands by name

Popular brands