manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Share
Download
Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download Page 326

Phaser 5400 Laser Printer Service Guide 

297

RRP 7.1 Laser Assembly 

(See 

PL 8.1 Xerographics

)

Removal

Caution: These components are susceptible to electrostatic 

discharge. Observe all ESD procedures to avoid damage.

Warning: Switch off the power and disconnect the Power Cord.

1.

Open the Rear Cover.

2.

Open the Top Cover and remove the Print Cartridge. Cover the cartridge to protect 
it from light.

3.

Remove the Left Side Cover (RRP 1.1 Left Side Cover).

4.

Remove the Top Cover Assembly (RRP 1.3 Top Cover Assembly).

5.

Remove the screw that secures the Right Side Cover to the Laser Cover.

6.

Remove the Front Cover (RRP 1.4 Front Cover).

7.

Remove the six screws that secure the Laser Cover to the printer. Move the top of 
the right cover to the right and remove the Laser Cover.

Figure 86 Laser Cover

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands