manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Experience fast and efficient printing with the Xerox 5400N - Phaser B/W Laser Printer. Easily navigate through troubleshooting with the Service Quick Reference Manual, available for free download on our website. Enhance your printing experience with this reliable and high-quality laser printer. Download the manual from manualshive.com.

Share
Download
background image

Phaser 5400 Laser Printer Service Guide 

309

RRP 8.4 Main Fan 

(See 

PL 9.1 Electrical (1 of 2)

)

Removal

Caution: These components are susceptible to electrostatic 

discharge. Observe all ESD procedures to avoid damage.

Warning: Switch off the power and disconnect the Power Cord.

1.

Remove the Lower Rear Cover (RRP 1.7 Lower Rear Cover).

2.

Remove the Rear Cover (RRP 1.9 Rear Cover).

3.

Remove the HCS if installed (RRP 10.1 1000-Sheet High Capacity 
Stacker [HCS]).

4.

Remove the Left Side Cover (RRP 1.1 Left Side Cover).

5.

Open the Top Cover and remove the Print Cartridge. Cover the cartridge to protect 
it from light.

6.

Remove the Top Cover Assembly (RRP 1.3 Top Cover Assembly).

7.

Remove the screw that secures the left edge of the HVPS Cover.

8.

Disconnect P/J165 from the LVPS PWB.

9.

Remove the three screws that secure the Fan Guard to the printer.

10.

Remove Fan Harness from all clamps.

11.

Remove the screw that secures the Main Fan to the printer. Remove the fan.

Replacement

Reinstall the components in the reverse order.

Figure 98 Main Fan

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5400N - Phaser B/W Laser Printer

DataCard CR500 Quick Install Manual preview
CR500
Brand: DataCard Pages: 17
DataCard CR500 User Reference Manual preview
CR500
Brand: DataCard Pages: 24
Samsung CLP 510N - Color Laser Printer Manual Del Usuario preview
CLP 510N - Color Laser Printer
Brand: Samsung Pages: 270
Samsung Bixolon SRP-270 Integrator'S Manual preview
Bixolon SRP-270
Brand: Samsung Pages: 13
Oki B930dn Guide Utilisateur preview
B930dn
Brand: Oki Pages: 222
Oki B930dn Brochure & Specs preview
B930dn
Brand: Oki Pages: 4
Oki B6250dn Guía Del Usuario preview
B6250dn
Brand: Oki Pages: 160
Zmorph VX Quick Start Manual preview
VX
Brand: Zmorph Pages: 16
Xerox VersaLink C405/N User Manual preview
VersaLink C405/N
Brand: Xerox Pages: 256
Cycjet ALT382 Manual preview
ALT382
Brand: Cycjet Pages: 26
Pantum M6500 series Faq preview
M6500 series
Brand: Pantum Pages: 126
Xerox EC8056 Getting Started preview
EC8056
Brand: Xerox Pages: 13
Partner RP-320 User Manual preview
RP-320
Brand: Partner Pages: 15
Oki B700 Series Installation Instructions preview
B700 Series
Brand: Oki Pages: 4
Velleman 3DPEN1 User Manual preview
3DPEN1
Brand: Velleman Pages: 44
Citizen CT-S310 User Manual preview
CT-S310
Brand: Citizen Pages: 3
Lexmark C53x Clearing Jams Manual preview
C53x
Brand: Lexmark Pages: 6
TAKE-A-LABEL TAL-3100C Operation Manual preview
TAL-3100C
Brand: TAKE-A-LABEL Pages: 12

Brands by name

Popular brands

Load more brands