manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Share
Download
Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download Page 382

Phaser 5400 Laser Printer Service Guide 

353

Removal

Warning: Switch off the power and disconnect the Power Cord.

1.

Lock the front casters on the 2000-Sheet Feeder.

2.

Remove the HCS, if installed 
(RRP 10.1 1000-Sheet High Capacity Stacker [HCS]).

3.

Remove Tray 1 from the printer.

4.

Remove the two screws that secure the printer.

Note: 

For safety reasons, have someone assist you in removing the 

printer and setting it in a safe place.

5.

Remove the printer.

6.

If a 500-Sheet Feeder is installed, remove the paper tray, remove the two screws 
that secure the 500-Sheet Feeder to the 2000-Sheet Feeder, and remove the 

500-Sheet Feeder.

Replacement

Reinstall the components in the reverse order.

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands