Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download

Page: 364 / 503

Phaser 5400 Laser Printer Service Guide

335

RRP 11.8 Feed Head Assembly

(See

PL 11.3 500-Sheet Feeder (3 of 3)

)

Removal

Warning: Switch off the power and disconnect the Power Cord.

Remove the printer from the 500-Sheet Feeder (RRP 11.1 500-Sheet Feeder
Removal).

Remove the paper tray from the feeder.

Remove the Front Cover (RRP 11.2 Front Cover).

Remove the Left Cover (RRP 11.3 Left Cover)

Disconnect P/J13A, P/J13P, and P/J135 from the Feed Head Assembly.

Remove the screw that secures the Feed Head to the feeder frame.

Push the right locking pin down and slide the right end of the Feed Head forward.

Push the left locking pin down and slide the left end of the Feed Head forward.

Slide the Feed Head forward and remove.

Replacement

Reinstall the components in the reverse order.

Figure 125 Feed Head Assembly

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Search results

Summary of Contents for 5400N - Phaser B/W Laser Printer

Reviews:

Related manuals for 5400N - Phaser B/W Laser Printer

Brands by name

Popular brands

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Search results

Summary of Contents for 5400N - Phaser B/W Laser Printer

Reviews:

Related manuals for 5400N - Phaser B/W Laser Printer

Brands by name

Popular brands