manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Share
Download
Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download Page 357

328

Phaser 5400 Laser Printer Service Guide

RRP 11.1 500-Sheet Feeder Removal 

(See 

PL 11.1 500-Sheet Feeder (1 of 3)

)

Removal

Warning: Switch off the power and disconnect the Power Cord.

1.

Remove the HCS, if installed 
(RRP 10.1 1000-Sheet High Capacity Stacker [HCS]).

2.

Remove Tray 1 from the printer.

3.

Remove the two screws that secure the printer to the Optional Paper Feeder.

Warning: To avoid possible personal injury associated with lifting 

heavy objects, have someone assist you in removing the 

printer and setting it in a safe place.

4.

Remove the printer.

Replacement

Reinstall the components in the reverse order.

Figure 118 Feeder Removal

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands