Xerox 5400N - Phaser B/W Laser Printer Service Quick Reference Manual Download Page 329

Page: 329 / 503

300

Phaser 5400 Laser Printer Service Guide

Remove the Left Side Cover (RRP 1.1 Left Side Cover).

Remove the Top Cover Assembly (RRP 1.3 Top Cover Assembly).

Remove the HVPS Cover (RRP 1.6 HVPS Cover).

Remove the BTR Assembly
(RRP 7.6 Bias Transfer Roller [BTR] Assembly).

Disconnect P/J186 (R) and P/J187 (W) from the HVPS PWB.

10.

Disconnect P/J177 and P/J178 from the Fuser Interlock Switch.

11.

Disconnect P/J162 from the LVPS PWB.

12.

Remove all disconnected harnesses from cable clamps.

13.

Remove the two screws that secure the right guide assembly.

14.

Guide harnesses through the printer frame as you remove the Right Print Cartridge
guide Assembly from the printer.

Note:

The Pin Link is not attached to the Guide Assembly and may

fall into the printer when the guide assembly is removed.

15.

Remove the Right Print Cartridge Guide Assembly and Pin Link from the printer.

Replacement

Reinstall the components in the reverse order.

Summary of Contents for 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Search results

Summary of Contents for 5400N - Phaser B/W Laser Printer

Reviews:

Brands by name

Popular brands

Xerox 5400N - Phaser B/W Laser Printer, Service Quick Reference Manual

Search results

Summary of Contents for 5400N - Phaser B/W Laser Printer

Reviews:

Brands by name

Popular brands