manualshive.com logo in svg

Treaton MPR6-03, User Manual

The Treaton MPR6-03 User Manual is a comprehensive guide that provides step-by-step instructions on how to set up and operate the MPR6-03 device. Designed with user convenience in mind, this manual can be easily downloaded for free from our website, ensuring a hassle-free experience.

Share
Download
background image

2.1 SpO

2

 Monitoring 

72 

2.1.4. SpO

2

 Monitoring using Masimo SET

®

 

technology 

Description 

This  section  provides  information  on  how  to  operate  a  device  equipped  with  a  pulse  oximetry 
module using Ma

simo SET® technology (MS-2040) to monitor: 

  saturation of arterial blood with oxygen, SpO

2

 

  photoplethysmogram, PPG 

  heart rate obtained from photoplethysmogram, PR 

  perfusion (filling) index  - the numerical value of the pulsating component of the regis-

tered signal due to the pulsation of arterial blood flow, PI. 

Masimo

®

, Masimo SET

®

, LNOP

®

, LNCS

®

 are registered trademarks of Masimo Corporation, USA 

If the device is equipped with the pulse oximetry module using Masimo SET

®

 

technology, the side panel of the connectors has a special rectangular con-
nector marked with a special sign.

 

 

Operating principle  

The  principle  of  operation  of  the  Masimo  SET®  pulse  oximetry  module,  like  a  conventional 
pulse oximeter, is based on different spectral absorption of oxyhemoglobin and reduced blood 
hemoglobin. The pulsating blood in the tissue is illuminated by radiation sources in the red and 
infrared  spectrum,  and  the  received  signals,  after  appropriate  processing,  make  it  possible  to 
determine the modulation coefficients of these light fluxes and, by their ratio, determine the oxy-
gen  saturation  of  blood  hemoglobin,  while  the  modulation  frequency  corresponds  to  the  pulse 
rate. The difference between Masimo SET® technology lies in the additional mathematical pro-
cessing of signals received in the red and infrared spectrum in order to compensate for interfer-
ence from light absorption by venous blood. 

Patents 

Masimo  SET

®

  technology  protected  by  the  respective  patents  listed  on  the  website 

www.masimo.com/patents.htm

. 

No Implied License 

Possession  or  purchase  of this  device  does  not convey  any  express  or  implied  license  to  use 
the device with unauthorized sensors or cables which would, alone or in combination with this 
device, fall within the scope of one or more of the patents relating to this device. 

WARNINGS! 

 

Explosion hazard. Do not use the device in the presence of flammable anesthetics or other 
flammable  substance  in combination  with  air,  oxygen-enriched  environments,  or  nitrous  ox-
ide. 

 

The device is to be operated by qualified personnel only. This manual, accessory directions 
for use, all precautionary information, and specifications should be read before use. 

 

The device should NOT be used as an apnea monitor. 

 

Pulse  rate  measurement  is  based  on  the  optical  detection  of  a  peripheral  flow  pulse  and 
therefore  may  not  detect  certain  arrhythmias.  The  pulse  oximeter  should  not  be  used  as  a 
replacement or substitute for ECG based arrhythmia analysis. 

 

A pulse oximeter should be considered an early warning device. As a trend towards patient 
deoxygenation is indicated, blood samples should be analyzed by a laboratory co-oximeter to 
completely understand the patient’s condition. 

 

Electric  shock  hazard.  Do  not  remove  the  device  cover.  An  operator  may  only  perform 
maintenance procedures specifically described in this manual. Refer servicing to the service 
center in repair of this equipment. 

Summary of Contents for MPR6-03


































































































































































































Reviews:

No comments

Related manuals for MPR6-03

Rabe TURBOSEED PRO Original Instructions Manual preview
TURBOSEED PRO
Brand: Rabe Pages: 65
Omnia 11 Quick Start Installation Manual preview
11
Brand: Omnia Pages: 8
Keiser M SERIES Manual preview
M SERIES
Brand: Keiser Pages: 82
Keiser M SERIES Calibration Instruction preview
M SERIES
Brand: Keiser Pages: 4
Campbell SkyVUE 8M Quick Deploy Manual preview
SkyVUE 8M
Brand: Campbell Pages: 2
IDS Dual Product Manual preview
Dual
Brand: IDS Pages: 2
Nabtesco Symphony NK-6 User Manual preview
Symphony NK-6
Brand: Nabtesco Pages: 26
Quanser QNET Physics and Dynamics Quick Start Manual preview
QNET Physics and Dynamics
Brand: Quanser Pages: 4
UniPix ATMOS Operation Manual preview
ATMOS
Brand: UniPix Pages: 24
M-Audio Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology... User Manual preview
Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...
Brand: M-Audio Pages: 25
MacDon R1 FR Series Operator'S Manual preview
R1 FR Series
Brand: MacDon Pages: 238
Ultrasport 331100000096 Assembly Instruction Manual preview
331100000096
Brand: Ultrasport Pages: 72
Wieland SMI 1001 Operating Manual preview
SMI 1001
Brand: Wieland Pages: 2
SHOWTEC 41370 Micro Spot Manual preview
41370 Micro Spot
Brand: SHOWTEC Pages: 22
Carestream CS 9300C User Manual preview
CS 9300C
Brand: Carestream Pages: 64
Daavlin UV Series Operation Manual preview
UV Series
Brand: Daavlin Pages: 55
Daavlin 1 Series Operation Manual preview
1 Series
Brand: Daavlin Pages: 19
LiteGait 300 Deluxe Operators & Service Manual preview
300 Deluxe
Brand: LiteGait Pages: 43

Brands by name

Popular brands

Load more brands