Thermo Scientific thermoscientific Vanquish Pumps C Operating Manual Download Page 26 | Manualshive

Page: 26 / 296

background image

2

•

Safety

Page 26

Pumps C, Pumps F ( VC-Pxx, VF-Pxx)

Operating Manual

2.4

Solvent and Additive Information

2.4.1

General Compatibility

To protect optimal functionality of the Vanquish system, observe these
recommendations on the use of solvents and additives:

•

The system must be used with reversed-phase (RP) compatible
solvents and additives only.

•

Use only solvents and additives that are compatible with all parts in
the flow path.

TIP

In a Vanquish Core system, normal-phase (NP) compatible solvents

and additives may be used if the VC-pumps and the VC-autosamplers are
modified with the components from the Normal-Phase (NP) kit. See

Normal-Phase Compatible Solvents and Additives (

NOTICE

If the system flow path includes a Vanquish charged aerosol detector,
observe the specific solvent and additive information for this detector.
Refer to the

Operating Manual

for the Vanquish charged aerosol

detector.

«
...
24
25
26
27
28
...
»

Summary of Contents for thermoscientific Vanquish Pumps C









































































































































































































































































































Reviews:

No comments

Related manuals for thermoscientific Vanquish Pumps C

Brand: GBC Pages: 8

Brand: KAPSCH Pages: 57

Brand: Zenbooth Pages: 60

Brand: JB-Lighting Pages: 60

Brand: DANLERS Pages: 2

Brand: Haas Automation Pages: 26

Brand: Garmin Pages: 20

Brand: Garden Treasures Pages: 2

i-limb access hand

Brand: Össur Pages: 246

PROPRIO FOOT PSX01

Brand: Össur Pages: 374

Brand: JBM Pages: 12

Brand: EFX Pages: 2

Brand: Daekyung Pages: 15

Brand: Vibration Research Corporation Pages: 333

Brand: Eurotops Pages: 8

Brand: KRATOS SAFETY Pages: 36

Brand: Tarter Pages: 18

Brand: laerdal Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands