Thermo Scientific thermoscientific Vanquish Pumps C Operating Manual Download Page 20 | Manualshive

Page: 20 / 296

background image

2

•

Safety

Page 20

Pumps C, Pumps F ( VC-Pxx, VF-Pxx)

Operating Manual

2.2

Intended Use

The device is intended to be part of the Vanquish system.

The intended use of the Vanquish system is to analyze mixtures of
compounds in sample solutions.

The device is for use by qualified personnel and in laboratory
environment only.

The device and Vanquish system are intended to be used as General
Laboratory Equipment (GLE).

They are not intended for use in diagnostic procedures.

Laboratory Practice

Thermo Fisher Scientific recommends that the laboratory in which the
Vanquish system is used follow best practices for LC analyses. This
includes among others:

•

Using appropriate standards

•

Regularly running calibration

•

Establishing shelf life limits and following them for all consumables
used with the system

•

Running the system according to the laboratory's verified and
validated 'lab developed test' protocol

«
...
18
19
20
21
22
...
»

Summary of Contents for thermoscientific Vanquish Pumps C









































































































































































































































































































Reviews:

No comments

Related manuals for thermoscientific Vanquish Pumps C

Brand: Olympus Pages: 86

Brand: ICS Schneider Messtechnik Pages: 124

Brand: Eclipse Combustion Pages: 46

Brand: Bard Pages: 2

Brand: OfiTE Pages: 21

Brand: Earthlite Pages: 4

Brand: YATEK Pages: 78

Brand: Campbell Pages: 2

Brand: Raven Pages: 17

Brand: Campbell Pages: 12

Brand: Halyard Pages: 88

Brand: Pari Pages: 50

Brand: Icare Pages: 42

Brand: Teac Pages: 76

Brand: Teac Pages: 3

Brand: Teac Pages: 50

Brand: Teagle Pages: 2

Brand: Yanmar Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands