Teledyne TS-C2500, User Manual

Page: 70 / 191

68

Operational Reference Genie_TS_Series GigE Vision Camera
Line Status All LineStatusAll Returns the current status of all available line
signals, at time of polling, in a single bitfield. The
order is Line1, Line2, Line3, ... (RO)
1.00
Expert
LineInverter Controls whether to invert the polarity of the
selected input or output line signal.
Line Inverter
False / True
1.00
Beginner
Input Line Detection Level lineDetectionLevel Specifies the voltage threshold required to
recognize a signal transition on an input line.
Threshold for TTL Threshold_for_TTL A signal below 0.8V will be detected as a Logical
LOW and a signal greater then 2.4V will be
detected as a Logical HIGH on the selected input
line.
Threshold for 12V Threshold_for_12V A signal below 2.0V will be detected as a Logical
LOW and a signal greater then 10V will be detected
as a Logical HIGH on the selected input line.
Threshold for 24V Threshold_for_24V A signal below 4.0V will be detected as a Logical
LOW and a signal greater then 20V will be detected
as a Logical HIGH on the selected input line.
1.00
Beginner
DFNC
Input Line Debouncing
Period lineDebouncingPeriod Specifies the minimum delay before an input line
voltage transition is recognizing as a signal
transition.
1.00
Beginner
DFNC
Output Line Source outputLineSource Selects which internal signal or event driven pulse
or software control state to output on the selected
line. Note, the LineMode feature must be set to
Output. The List of supported output line sources is
product-specific. The
Event Control section
provides details and timing diagrams for the
supported trigger modes.
Off Off Line output is Open
Software Controlled SoftwareControlled The OutputLineValue feature changes the state of
the output
Pulse on: Start of Frame PulseOnStartofFrame Generate a pulse on the start of the Frame Active
event
Pulse on: Start of Exposure PulseOnStartofExposure Generate a pulse on the ExposureStart event. This
option is typically used to trigger a strobe light.
Pulse on: End of Exposure PulseOnEndofExposure Generate a pulse on the ExposureEnd event. This
option is typically used to trigger a strobe light.
Pulse on: Start of Readout PulseOnStartofReadout Generate a pulse on the ReadoutStart event.
Pulse on: End of Readout PulseOnEndofReadout Generate a pulse on the ReadoutEnd event.
Pulse on: Valid Frame
Trigger
PulseOnValidFrameTrigger Generate a pulse on the ValidFrameTrigger event.
Pulse on: Invalid Frame
Trigger
PulseOnInvalidFrameTrigger Generate a pulse on the InvalidFrameTrigger
event.
Pulse on: Start of Acquisition PulseOnStartofAcquisition Generate a pulse when the AcquisiontStart event
occurs
Pulse on: End of Acquisition PulseOnEndofAcquisition Generate a pulse when the AcquisiontStop event
occurs
Pulse on: End of Timer 1 PulseOnEndofTimer1 Generate a pulse on the TimerEnd 1 event.
Pulse on: End of Counter 1 PulseOnEndofCounter1 Generate a pulse on the CounterEnd 1 event.
Pulse on: Input 1 Event PulseOnInput1 Generate a pulse on the Input signal 1 event
Pulse on: Input 2 Event PulseOnInput2 Generate a pulse on the Input signal 2 event
Pulse on: Input 3 Event PulseOnInput3 Generate a pulse on the Input signal 3 event
Pulse on: Input 4 Event PulseOnInput4 Generate a pulse on the Input signal 4 event
Pulse on: Software
Command
PulseOnSoftwareCmd Generate a pulse on the Input of a Software
Command
1.00
Beginner
DFNC
Output Line Pulse Signal
Activation
outputLinePulseActivation Specifies the input line activation mode to trigger
the OutputLine pulse.
Rising Edge RisingEdge Specifies that the trigger is considered valid on the
rising edge of the source signal.
1.00
Beginner
DFNC