Tektronix 492, 492P Service Manual Download

Page: 146 / 303

Maintenance—492/492Ρ Service Vol. 1 (SN B030000 & up)

■

w k

Fig. 4-23. Jumper positions between T1077 and T1075 versus frequency compensation fo r the 14-22 MHz Oscillator.

Apply 1 με markers from the time mark generator to

the RF INPUT. Set the Center Frequency to 10 MHz and

adjust the REF LEVEL to display the comb of markers. Set

the FREQ SPAN/DIV to 100 kHz and center a marker on

the display with the center FREQUENCY control. Reduce

the FREQ SPAN/DIV to 50 kHz.

Adjust the Gain potentiometer R2063 so there is ap

proximately one marker signal per division near the display

center. The 2nd LO is now being swept beyond its normal

tuning range;

the actual

span

approximately

1 MHz/division. If the sweep linearity of the 2nd LO is satis

factory, each marker over the center eight divisions will align

with a graticule line.

Observe the center eight divisions of the display and

adjust linearity as follows;

Adjust R1070 so the spacings between marker sig

nals are equal at the right and left sides of the display.

Decrease the resistance if the marker spacing on the

right side is less than the left and increase the resistance

if the spacing is greater on the right than the left side.

Adjusting R1070 will change the 2nd LO center frequen
cy causing the center marker to shift position. Increase

the FREQ SPAN/DIV to 100 kHz, recenter the marker,

then return the SPAN/DIV to 50 kHz.

Decrease R1068 if the spacing between markers

at the center of the display is closer than the markers at

the right or left edge. Increase the value if the spacing at

center screen is wider.

Adjustment of either R1070 or R1068 will affect

span/div. Readjust R2063 for one marker/division near

the center part of the display.

Repeat parts 1—3 until the best uniform signal

spacing over the center eight divisions of the display, is

obtained.

Remove the 750 Ω resistor between the 2nd LO

Sweep Input and the junction of R2063 and pin 2 of U2063

(part b of this procedure). This completes the coarse linear

ity adjustment.

S. Fine Linearity Adjustment

Apply 5

μ ε

markers from the time mark generator to

the RF INPUT. Center the frequency of the 2nd LO by

switching the FREQ SPAN/DIV to 100 kHz then down to

20 kHz.

Center a pair of markers on the display with the FRE

QUENCY control.

Change the Vertical Display to 2 dB/DIV, FREQ

SPAN/DIV to 20 kHz, and adjust the REF LEVEL for a sig
nal amplitude of two to three divisions.

Adjust R2063 (Gain) so the signals are separated ex

actly six major divisions.

REV

JUN 1983

4-33

Summary of Contents for 492, 492P
















































































































































































































































































































Search results

Summary of Contents for 492, 492P

Reviews:

Related manuals for 492, 492P

Brands by name

Popular brands

Tektronix 492, 492P, Service Manual

Search results

Summary of Contents for 492, 492P

Reviews:

Related manuals for 492, 492P

Brands by name

Popular brands