TECO F33 Series, Instruction Manual, Page: 9 / 192

6 Introduction
1.4 Standards
The variable speed drives described in this instruction
manual comply with the standards listed in Table 1. For
the declarations of conformity and manufacturer’s cer-
tificate, contact your supplier for more information .
1.4.1Product standard for EMC
Product standard EN(IEC)61800-3, second edition of
2004 defines the:
First Environment (Extended EMC) as environment that
includes domestic premises. It also includes establish-
ments directly connected without intermediate trans-
formers to a low voltage power supply network that
supplies buildings used for domestic purposes.
Category C2: Power Drive System (PDS) of rated volt-
age<1.000 V, which is neither a plug in device nor a
movable device and, when used in the first environ-
ment, is intended to be installed and commissioned
only by a professional.
Second environment (Standard EMC) includes all other
establishments.
Category C3: PDS of rated voltage <1.000 V, intended
for use in the second environment and not intended for
use in the first environment.
Category C4: PDS or rated voltage equal or above
1.000 V, or rated current equal to or above 400 A, or
intended for use in complex systems in the second envi-
ronment.
The variable speed drive complies with the product
standard
EN(IEC) 61800-3:2004 (Any kind of metal screened
cable may be used). The standard variable speed drive
is designed to meet the requirements according to cat-
egory C3.
By using the optional “Extended EMC” filter the VSD ful-
fils requirements according to category C2,
3 3
Rated current (A)
continuous
-0003=2.5 A
-
-1500=1500 A
4 4 Protection class
20=IP20
54=IP54
5 5 Control panel
–=Blank panel
C=Standard panel
6 6 EMC option
E=Standard EMC
(Category C3)
F=Extended EMC
(Category C2)
I=IT-Net
7 7
Brake chopper
option
–=No chopper
B=Chopper built in
D=DC+/- interface
8 8
Stand-by power sup-
ply option –=No SBS
S=SBS included
- 9
Safe stop option
(Not valid for
0003-0046) –=No safe stop
T=Safe stop incl.
(Only 0090-1500)
9 10 Brand label
10 -
Painted VSD
(Only valid for
0003-0046) A=Standard paint
B=White paint
RAL9010
11 11
Coated boards,
option
A=Standard
boards
V=Coated boards
12 12 Option position 1 N=No option
C=Crane I/O
E=Encoder
P=PTC/PT100
I=Extended I/O
S=Safe Stop (only
0003-0046)
13 13 Option position 2
14 14 Option position 3
15 15
Option position, com-
munication
N=No option
D=DeviceNet
P=Profibus
S=RS232/485
M=Modbus/TCP
16 16 Software type A=Standard
17 17
Motor PTC. (Only
valid for 0003-0046) N=No option
P=PTC
18 18
Gland kit.
(Only valid for 0003-
0046)
–=Glands not
included
G=Gland kit
included
Position
for
0003-
0046
Position
for
0060-
1500
Configuration
WARNING: In a domestic environment this
product may cause radio interference, in
which case it may be necessary to take
adequate additional measures.
WARNING: The standard VSD, complying with
category C3, is not intended to be used on a
low-voltage public network which supplies
domestic premises; radio interference is
expected if used in such a network. Contact
your supplier if you need additional
measures.
CAUTION: In order to comply fully with the
standards stated in the Manufacturer’s
Declaration ANNEX IIB, the installation
instructions detailed in this instruction
manual must be followed to the letter.
!