TECO F33 Series, Instruction Manual, Page: 131 / 192

128 Functional Description
11.5.4 Digital Outputs [540]
Submenu with all the settings for the digital outputs.
Digital Out 1 [541]
Sets the function for the digital output 1.
NOTE: The definitions described here are valid for the
active output condition.
Default: Ready
Off 0
Output is not active and constantly
low.
On 1
Output is made constantly high, i.e.
for checking circuits and trouble
shooting.
Run 2
Running. The VSD output is active =
produces current for the motor.
Stop 3 The VSD output is not active.
0Hz 4
The output frequency=0±0.1Hz when
in Run condition.
Acc/Dec 5
The speed is increasing or decreasing
along the acc. ramp dec. ramp.
At Process 6 The output = Reference.
At Max spd 7
The frequency is limited by the Maxi-
mum Speed.
No Trip 8 No Trip condition active.
Trip 9 A Trip condition is active.
AutoRst Trip 10 Autoreset trip condition active.
Limit 11 A Limit condition is active.
Warning 12 A Warning condition is active.
Ready 13
The VSD is ready for operation and to
accept a start command. This means
that the VSD is powered up and
healthy.
T= T
lim
14
The torque is limited by the torque
limit function.
I>I
nom
15
The output current is higher than the
motor nominal current [224], reduced
according to Motor ventilation [228],
see Fig. 71.
Brake 16
The output is used to control a
mechanical brake.
Sgnl<Offset 17
One of the AnIn input signals is lower
than 75% of the threshold level.
Alarm 18
The max or min alarm level has been
reached.
Pre-Alarm 19
The max or min pre alarm level has
been reached.
541 DigOut 1
Stp Ready
A
Max Alarm 20
The max alarm level has been
reached.
Max PreAlarm 21
The max pre alarm level has been
reached.
Min Alarm 22
The min alarm level has been
reached.
Min PreAlarm 23
The min pre alarm Level has been
reached.
LY 24 Logic output Y.
!LY 25 Logic output Y inverted.
LZ 26 Logic output Z.
!LZ 27 Logic output Z inverted.
CA 1 28 Analogue comparator 1 output.
!A1 29 Analogue comp 1 inverted output.
CA 2 30 Analogue comparator 2 output.
!A2 31 Analogue comp 2 inverted output.
CD 1 32 Digital comparator 1 output.
!D1 33 Digital comp 1 inverted output.
CD 2 34 Digital comparator 2 output.
!D2 35 Digital comp 2 inverted output.
Operation 36
Run command is active or VSD run-
ning. The signal can be used to con-
trol the mains contactor if the VSD is
equipped with Standby supply option.
T1Q 37 Timer1 output
!T1Q 38 Timer1 inverted output
T2Q 39 Timer2 output
!T2Q 40 Timer2 inverted output
Sleeping 41 Sleeping function activated
Crane Deviat 42 Tripped on deviation
PumpSlave1 43 Activate pump slave 1
PumpSlave2 44 Activate pump slave 2
PumpSlave3 45 Activate pump slave 3
PumpSlave4 46 Activate pump slave 4
PumpSlave5 47 Activate pump slave 5
PumpSlave6 48 Activate pump slave 6
PumpMaster1 49 Activate pump master 1
PumpMaster2 50 Activate pump master 2
PumpMaster3 51 Activate pump master 3
PumpMaster4 52 Activate pump master 4
PumpMaster5 53 Activate pump master 5
PumpMaster6 54 Activate pump master 6
All Pumps 55 All pumps are running
Only Master 56 Only the master is running
Loc/Rem 57 Local/Rem function is active
Standby 58 Standby supply option is active