Siemens HiPath 1100 Programming Manual Download Page 105

Page: 105 / 241

General settings

105

Step by step

Billing

Call charge unit

To show call charges in currency units you must specify

a call charge factor. Pulses are multiplied by this factor.

A call charge unit consists of a pulse transmitted to the

public exchange, over the line, that displays call charge

information according to the type of line (external or IS-

DN), call type (local, DDD, International, etc.) and other

parameters specified by the carrier.

The default value is the "0" comma slot and the "00001"

factor.

Required:

Programming mode must be activated (*95

31994).

emi

Enter the programming code.

Set the call charge factor (9 digits).

Enter the decimal separator position (0 to 3)

Examples:

– for R$ 0.12: 000000012 and 2 (comma position)
– for R$ 2.00: 00002 and 0 (comma position)
– for R$ 123456.789: 123456789 and 3 (comma po-

sition)

Initial status for programming mode.

Multiplier for call charge factor

This setting specifies the multiplier for call charge fac-

tors.

A callback can only be scheduled for an MSN.

MSN numbers must be programmed and must

have attendants.

On HiPath 1100 systems, the Billing facility (Call

cost limit by extension) is only available for digital

trunks (ISDN and CAS). Please consult your local

carrier to know if this service is provided.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands