Siemens HiPath 1100 Programming Manual Download Page 18

Page: 18 / 241

Step by step

Programming mode

Flexible numbering

The pre-programmed parameters for the system num-

bering plan, and the features access codes as well may

have their numbers changed to fit their communication

platform using the management software HiPath 1100

Manager. For this procedure, please call the system

technical support.

Activating system programming

Lift the handset at the programmer’s extension slot.

qmi

Enter the code to activate system programming.

Enter the system password (default is 31994 - Changing

system password

page 112).

You will hear a tone indicating that you have now ac-

cessed the programming mode.

Audible Tones in the programming mode (Brazil)

• Correct entry: 1 beep/confirmation tone.

• Incorrect entry: 3 beeps. The program will then re-

vert back to the initial screen of the programming

mode.

• After completing the programming steps, the sys-

tem responds with a confirmation tone and finalizes

the setting configuration. The program will then re-

vert back to the initial screen of the programming

mode.

Fax/DID - Virtual message ports

740 to 743

USB/CAPI line

100

Substitution for * and #

75 and 76 (accordingly)

Description

HiPath 1120 HiPath 1150 HiPath 1190

System programming can only be executed us-

ing the

first slot on an analog extension

of the

interface (default extension 11) equipped with an

analog

extension (MF) or on a

-type system

telephone or in the first slot of an

optiPoint

-type

system telephone. Programming cannot be

made on two extensions at the same time.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands