Siemens HiPath 1100 Programming Manual Download Page 180

Page: 180 / 241

Step by step

Relay and sensor on the HiPath 1120

180

Time between attempts for activating the
sensor

This setting specifies a timeout after which a new at-

tempt is made to call an internal or external number, as-

suming that the line was busy on the previous attempt.

The default setting is 3 minutes.

Required:

Programming mode must be activated (*95

31994).

did

Enter the programming code.

...

Select a timeout until the next attempt (0 to 10 min-

utes).

Initial status for programming mode.

MSN Assignment for the Sensor

This settings specifies an MSN for the system to be

used for outgoing calls. By using this MSN, the called

party is able to identify the origin of the call. For in-

stance, this would be the case for an alarm.

The default configuration does not specify an MSN.

Required:

Programming mode must be activated (*95

31994).

die

Enter the programming code.

dde

...

ehd

Enter the slot for the MSN number.

Initial status for programming mode.

Delete

Required:

Programming mode must be activated (*95

31994).

die

Enter the programming code.

dde

...

ehd

Enter the slot for the MSN number.

Press the key to remove it.

Initial status for programming mode.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands