Siemens HiPath 1100 Programming Manual Download Page 4

Page: 4 / 241

Step by step

How to use this manual

The steps for programming the system are presented

sequentially in graphic format under the column "Step

by Step" on the left side of each page.

Meaning of symbols:

Press the Flash/Fil key.

Lift the handset.

Replace the handset.

Start conversation.

...

Enter numbers, keys, passwords, internal or external

phone numbers, etc.

Wait to hear an audible tone through the handset or

speaker.

An extension is calling.

When enabling certain functions and procedures, a long

beeping tone means the activation was successful).

When enabling certain functions and procedures, short

beeping tones mean the activation failed).

System support technician

The system’s support technician is generally the person

responsible for programming your HiPath 1100. The sys-

tem’s support technician is equipped with the appropri-

ate tools and information to do this.

Assistance with troubleshooting

Contact your system’s support technician. If the prob-

lem is not solved, the support technician should call

Technical Support.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands