Siemens HiPath 1100 Programming Manual Download Page 46

Page: 46 / 241

Step by step

External line settings

Enter the next number for the analog trunk.

Press this key.

Initial status for programming mode.

Reseizure timeout for an external line

There is a timeout for reseizing an external line. Once an

outgoing call has ended the line will remain blocked dur-

ing the specified timeout.

Required:

Programming mode must be activated (*95

31994).

efm

Enter the programming code.

...

Enter the length of time (05 to 99) for the Flash signal,

where 05 = 500 ms (default) to 99 = 9900 ms.

Initial status for programming mode.

Maximum time between rings for an
incoming call

This consists of the time interval between two call puls-

es from the local carrier (approximately 6 seconds). At

the end of this time interval, the system disconnects

from the external line and gets ready to receive other

calls.

In some countries the pause between pulses is longer

than 6 seconds. Here you can specify the setting as you

prefer.

Required:

Programming mode must be activated (*95

31994).

When the line is programmed directly, the de-

fault duration of the flash of the line is 240ms

and when the line is programmed with another

PABX system, the default duration of the flash is

100ms.

Valid only for analog trunks.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands