Siemens HiPath 1100 Programming Manual Download Page 130

Page: 130 / 241

Step by step

Report

130

Report

Information about calls received and made is stored in

the system’s memory HiPath 1100. CDR records can be

reviewed in the following manner:

• By using a PC or printer connected through a serial

interface.

• By using a PC connected on a local network.

The tickets list can be viewed on a

Billing Application

installed in the PC or through Windows’

Hyper Termi-

nal

• For the Windows’

Hyper Terminal

the HiPath 1100

provides local control of ticket purchasing at any

time through a series of commands that can be pro-

grammed into the application interface with the

switch.

– Interface commands:

Command

Description

\nticket_start\n This command will be sent by the

user (Application) to the PABX, re-

questing that the stored tickets start

being sent.

\nticket_stop\n

This command will be sent by the

user (Application) to the PABX, re-

questing that the stored tickets stop

being sent.

After receiving and accepting those commands,

new tickets or tickets that are still stored will not

be transmitted to the PABX.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands