Siemens HiPath 1100 Programming Manual Download Page 77

Page: 77 / 241

Programming an extension

Step by step

Press this key.

Initial status for programming mode.

Overflow extension

An overflow extension receives calls when the exten-

sion called is not available.

Examples:

• The extension called is activated for room monitor-

ing (Babyphone)

• The extension that was programmed as the first at-

tendant is currently assigned as internal entrance

telephone

• No extension is configured (all extensions were de-

leted using the code "42").

By default, the first extension of the system is config-

ured as the overflow extension for Busy signal or Wrong

Number.

Required:

Programming mode must be activated (*95

31994).

egf

Enter the programming code.

e . g

Choose a list for call forwarding:

= No answer

= Busy

= Wrong number

Enter the extension number (e.g. 12 /102) to be added

to the list.

Initial status for programming mode.

The system allows automatic detection of the

flash time using the "Flash detection time on the

extension - *9495" feature - see User Manual.

The overflow extension is accessed using your

own internal number.

The overflow extension cannot be configured or

used for Fax.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands