Siemens HiPath 1100 Programming Manual Download Page 86

Page: 86 / 241

Step by step

Programming an extension

Press this key.

Initial status for programming mode.

Pulses for call charges on an analog ex-
tension

This sends pulses to be charged for calls on an analog

extension (12kHz/16kHz). With this feature, an exten-

sion’s telephone set can display the number of pulses

or the amount charged for the call.

Required:

Telephone with a display and programming

mode activated (*95 31994).

dhe

Enter the programming code.

Enter the analog extension number (e.g., 11/101).

Activate/Disable transmission of billing pulses:

= Activated

= Deactivated (default)

Enter the next analog extension number.

Press this key.

Initial status for programming mode.

If the telephone does not have a microphone

(e.g. analog telephones, optiPoint Entry and Ba-

sic) the subscriber hears a busy signal when pro-

gramming the code.

Please refer to the documentation provided with

the telephone set connected to the extension to

find out if a billing indication is supported and

which transmission mode is used.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands