Siemens HiPath 1100 Programming Manual Download Page 91

Page: 91 / 241

Programming an extension

Step by step

Modem extension

This setting specifies the extension where the modem

will be connected for serial remote access.

By default, no extension is configured.

Required:

Programming mode must be activated (*95

31994).

dli

Enter the programming code.

Enter the extension number (e.g. 11/101).

Initial status for programming mode.

External-to-external transfer

This feature allows a specified extension to transfer an

external call (incoming or outgoing) to another external

call.

Required:

Programming mode must be activated (*95

31994).

dme

Enter the programming code.

Enter the extension number (e.g. 11/101).

Activate/deactivate transfer:

= Activated

= Deactivated (default)

Press this key.

Initial status for programming mode.

An external-to-external transfer can only be

made when at least one of the lines is a digital

line and one of the calls is outgoing.

An external-to-external transfer over an analog

line is terminated in the following three situa-

tions:

• Elapsed timeout for external-to-external con-

nection (Code 218)

• When a busy signal is detected

• Type of answering signal (Code 158).

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands